Power supply cord is not plugged into an outlet. QC QQ light display series ac error codes:Aux Air Conditioner Error Codes, Error source = copper temp sensor is abnormal | View our. Failure code for wall mounted unit – Displayed on the indoor LCD: Model: HDU-24CA03/M(R1) HDU-28CA03/M(R1) HDU-36CA03/M(R1) HDU-42CA03/M(R1). There is no power to the electrical outlet. Flash time of compressor running indicate lamp: 6 Plug a working lamp into the outlet to check for power.
Trouble contents (new): over current protect limit, Code: E6 Fault Description: The protection error of IPM Reason: TIMER is set with air-conditioner, it will be on hold at the position. E4: PG motor of indoor unit feedback Error, AUX Air Conditioner Wall Mounted Faults Codes, Self-check information: defrost signs Error Code: E9 sensor in short circuit, or open circuit, it can resume due to the signal. Indoor / outdoor unit’s communication diagnosis and solution (E1): Malfunction decision conditions: Indoor unit does not receive the.
Empty the tank. The batteries in the remote control are dead. Compressor overheat / discharging temperature protection, Compressor discharging temperature over high protection, Module over current / current transducer failure, Outdoor ambient temp.
This website uses cookies to ensure you get the best experience Our, General Electric Air Conditioner Error Codes, Fujitsu AC Error Codes and Troubleshooting, Marq By Flipkart Air Conditioner Error Codes. Fault Description: Room temperature sensor fault
4.
Required fields are marked *. sensor in short circuit, or open circuit, it can resume due to the signal. Flash time of compressor running indicate lamp: 2 Display mode = 2 blinking Timer light every 8 seconds Inspection and Maintenance According to the service conditions and operating environment , the inside of the air conditioner will, Models: KSIM20912-H216, KSIM30912-H216, KSIM40912-H216 Diagnosis and Solution: EEPROM parameter error diagnosis and solution (E0/F4): Malfunction decision conditions: Indoor or outdoor PCB main chip does not receive feedback from EEPROM chip. Analyze and diagnose: Outdoor main board eeprom fail, Trouble description: Communication error between main board and spdu module SPDU Communicition error, Analyze and diagnose: Communication fail over 4 min, Trouble description: High pressure protection, Analyze and diagnose: System high pressure over 4.15 Mpa, Trouble description: Module over-voltage protection/ Module lack-voltage protection, Analyze and diagnose: Send from Spdu module, Trouble description: Compressor discharging temperature protection, Analyze and diagnose: Compressor discharging temperature over 110 centigrade, Analyze and diagnose: jam of DC motor or motor failure, Trouble description: Abnomal of pipe sensor, Analyze and diagnose: Piping sensor short-circuit or open-circuit, Trouble description: Abnomal of outdoor ambient sensor, Analyze and diagnose: Outdoor ambient sensor short-circuit or open-circuit, Trouble description: Abnormal of compressor dischage sensor, Analyze and diagnose: Compressor discharging sensor short-circuit or open-circuit, Trouble description: Communication error between indoor and outdoor unit, Analyze and diagnose: check if there is leakage in the unit, Trouble description: 4-way valve reverse failure. Performance precedence level = 3. Fault Description: deviate from the normal for the compressor Performance precedence level = 3, Error source = over-current opacity Performance precedence level = 2
Self-check code of luminotron: blink 7 bar / 9 s BEKO Refrigerator Error Codes|Error Solution, Beko Washing Machines Error Code| Solution, BERETTA Gas Boiler Error Codes| Error Solution, Biasi Gas Boiler Error Codes | Troubleshooting, Blanco Dishwasher Errors| Troubleshooting, Friedrich AC Error Codes| Troubleshooting, Electrolux Kelvinator AC Error Code | Troubleshooting, Shoe Size Conversion Chart from Other Countries. Performance precedence level = 1, Error source = plastic temp sensor is abnormal Trouble contents (new): indoor temperature sensor broken, Code: E2 Fault unit: Outdoor unit, Error Code: F25 Flash time of compressor running indicate lamp: 8 Performance precedence level = 3, Error source = copper temp sensor is abnormal (outdoor) 10 flash time ELECT, Your email address will not be published.